Products

ATEX Approved Pressure and Vacuum Feedthroughs

Series MF - Feedthroughs for multiple elements

A single access port into an enclosure or process vessel is all that is needed to allow multiple probes, sensors, etc., to pass through an environmental or pressure boundary using a single feedthrough assembly.

Series MF feedthroughs can seal multiple elements within a single assembly including typically up to 40 x 1.0mm dia., up to 27 x 3.0mm or up to 7 x 6.0mm elements. Please refer to the table for further details of feedthrough capacity and sizes of elements.

There are five body sizes having 1/8”, 1/4”, 1/2”, 3/4” and 1”process connections in either BSPT (conical gas or DIN 2999 ‘R’) and NPT threads.

Spectite® feedthroughs are designed for ease of assembly and installation. Elements can be adjusted, removed and replaced when not under pressure or vacuum conditions.
  • ATEX Approved to Ex II 2 GD, Ex d IIC Gb / Ex e IIC Gb, Ex ta IIIC Da
  • Saves time and costs as multiple sensors pass through one feedthrough
  • Immersion length of each element can be easily adjusted
  • Five sizes of sealed feedthrough for probes, sensors, etc.
  • Designed for carrying multiple elements
  • Suitable for a mixture of sizes and types of elements
  • Pressure range: Vacuum to 700 bar*
  • Temperature range: -60°C to +450°C*
  • 316L Body (and seat where applicable). Follower and cap in 303 or 304
  • Reusable fitting – sealant and internal components replaceable
  • * Dependent on sealant and fitting selected

Enquiry Form

1. Thread Size Required


  see table

2. Element diameter


 see table

3. No. of Elements


 see table

4. Sealant Type


 see table

4. Quantity Required


Contact Details


Company Name


Your Name


Email


Telephone


Additional Information


If your enquiry is for more than one style of sensor, please email us with your requirements or use the box below



Send Enquiry  
BACK TO TOP
ATEX Thermocouples with Pot Seal

ATEX Thermocouples with Die Cast Alloy Head

ATEX Thermocouples with Die Cast Alloy Head and Process Thread

ATEX Thermocouples with St. / Steel Head

ATEX Thermocouples with St. / Steel Head and Process Thread

ATEX Thermocouples with Dual Entry Head

ATEX Thermocouples with Dual Entry Head and Process Thread

ATEX Thermocouples with Spring loaded terminal block

ATEX Thermocouples with Terminal Entry Gland

ATEX Thermocouples with Terminal Entry Gland and Process Thread

ATEX Spring Loaded Thermocouples

ATEX Thermocouple Feedthroughs
ATEX RTD Pt100 Sensors with Pot Seal

ATEX RTD Pt100 Sensors with Die Cast Alloy Head

ATEX RTD Pt100 Sensors with Die Cast Alloy Head and Process Thread

ATEX RTD Pt100 Sensors with St. / Steel Head

ATEX RTD Pt100 Sensors with St. / Steel Head and Process Thread

ATEX RTD Pt100 Sensors with Dual Entry Head

ATEX RTD Pt100 Sensors with Dual Entry Head and Process Thread

ATEX RTD Pt100 Sensors with Spring loaded terminal block

ATEX RTD Pt100 Sensors with Terminal Entry Gland

ATEX RTD Pt100 Sensors with Terminal Entry Gland and Process Thread

ATEX Spring Loaded RTD Pt100 Sensors
ATEX 4 to 20mA Indicators

ATEX Temperature Transmitters

ATEX Compression Fittings

ATEX Terminal Heads

ATEX Pressure and Vacuum Feedthroughs



© 2014- TC Measurement & Control Pty Ltd, PO Box 7777, Oakleigh, VIC 3166
Tel.: 03 9543 8433, Fax: 03 9543 8466, Email: info@tcaus.com.au